Call to reach a local rooferColumbus, GA 31901
Call (833) 751-2102
Call to reach a local rooferCall now(833) 751-2102
Free estimate
Serving Muscogee County

Metal Roof Repair in Columbus, GA

Repairing metal roofs and metal trim in Columbus and the towns around it, where dents, lifted seams and loose fasteners show after storm wind.

Call (833) 751-2102Free estimate
  • Roof repair and full replacement
  • Storm and tornado roof damage
  • Phenix City and Fort Benning area

Get a fast quote

Fastest: call (833) 751-2102. Or send this and we call you back.

By sending this form you agree that Columbus Roofing may call or text you at the number provided about this request. Consent is not a condition of purchase. Message and data rates may apply. See our Privacy Policy.

Metal Roof Repair

Metal Roof Repair: what it covers

Quick answer

A metal roof sheds water through overlapping panels fixed by screws or clips. After a storm a roofer checks the panels for dents and lifted seams, the trim and flashing for looseness, and the fasteners for pull, and repairs or replaces each part in place.

Metal Roof Repair illustration for Columbus, GA

Metal roofing is durable, and that is the reason its damage is often overlooked. A panel can be dented, a seam can be lifted and a fastener can pull out of its washer while the roof still looks sound from the ground. Each of these is a leak waiting for the next storm, and each is quicker to fix in its early stage than after water has got underneath.

Storm wind is the usual cause of metal roof damage in this area. The 1997, 2007 and 2009 tornado records in the FACTS sheet are reasons to look at metal panels, ridge caps and trim closely after a named event, because debris and wind marks show on metal very clearly.

This page covers the common metal roof repairs, how a roofer checks them and what the written scope should include. The panels are repaired in place where possible, and replaced where they cannot be made sound.

Service area
Columbus & Muscogee County
Availability
Call to reach a local roofer
Warning signs

Signs you need metal roof repair

Metal is slippery when wet and can cut hands and feet. Do not walk a metal roof in rain or on a steep slope. Let the roofer work with fall protection and the right footwear.

  • Dents in the panel ribs or the flat faces, especially on the storm-facing side
  • Seams or laps that have lifted, opened or separated at the edges
  • Screws or clips that have backed out, pulled through or rusted
  • Trim, ridge caps or valley metal that has bent, torn or come loose
  • Rust spots or scratches that have broken the protective finish
  • Stains on the ceiling below a seam or a fastener line after rain
Options

Types and options for metal roof repair

Fastener and clip repair

Replacing pulled screws and failed clips, the most common metal roof repair after a windy event.

Panel and seam repair

Replacing dented or split panels, and re-joining seams that have lifted, with the same profile where it can be matched.

Trim, ridge and valley repair

Replacing bent or torn trim, ridge caps and valley metal that the storm has loosened.

Still stuck? We pick up 24/7.

If it's an emergency, call now. For non-urgent metal roof repair, send the form and we'll call you back.

Call (833) 751-2102Get a quote

Why does a dent on metal matter if the roof still keeps water out?

Because a dent can crack the finish, and a cracked finish lets rust start, while a dent on a seam can stop the seam from closing properly.

A dent in a metal panel is not always a leak, but it is a sign that the finish may have cracked at the dent. Once the coating is broken, moisture and salt reach the bare metal, and rust begins. A dent on a seam or a lap is more serious, because it can stop the seam from closing and let water through in the next heavy rain.

A roofer checks each dent for its position and its effect. A dent in a flat face away from a seam may be left and recorded, and a dent at a seam is reset or replaced.

  • Check the finish at each dent for cracking
  • A dent on a seam is treated as a leak risk
  • Record dents that are left in place

What causes a metal fastener to fail?

Wind lift, thermal movement and fasteners that were driven too tight or at the wrong angle. Pulled fasteners leave holes that let water in around the screw.

Metal panels move with the temperature, and the fasteners move with them. Over time a fastener can work loose, and a strong wind can lift a panel enough to pull the screw through its washer. A screw driven too tight can crack the washer, and one driven at the wrong angle can strip its threads.

The repair is to replace the failed fastener with one of the correct length and type, and to check the panel around it for cracking. A pulled screw that is simply re-driven will fail again.

  • Pulled screws are replaced, not re-driven
  • Washers checked for cracks after tightening
  • Clips replaced where they have failed

Can a metal roof be patched or does a panel have to be replaced?

A small hole or a short split can be patched. A panel that is split along its length, or dented across a seam, is replaced with the same profile.

Patching metal is a sound repair for a small hole or a short split, using a patch and the sealant the maker names. A panel that is split along its length, bent across a seam or dented so badly that it cannot shed water is replaced. Where the profile can no longer be matched, the roofer explains the trade-off between a visible patch and a larger job.

A roofer should say in writing which of these applies, so the homeowner chooses with the facts.

  • Small holes and short splits: patch
  • Split panels and seam damage: replace
  • Profile mismatch: explained before the work

What belongs in the metal roof record?

Each panel, seam and fastener by position, the state found, the repair made and the material used, with photographs before and after.

A metal roof record should name the panels by position, the seams by number and the fasteners by line. It should record the state found, the repair made and the material used. Photographs before and after show what the storm did and what the repair restored.

Keep the record with the storm inspection. A metal roof with a documented repair history is easier to insure and to sell.

  • Panels and seams named by position
  • The material and fastener used
  • Photographs before and after each repair
Our process

How our metal roof repair visit works

  1. Walk the roof from a safe position

    The roofer checks the panels, seams and trim from the ridge and the edges, marking each dent, lift and loose fixing. Metal is slippery when wet, so the roof is not walked in rain.

  2. Check the fasteners and the clips

    Each marked area is checked for fastener pull and clip failure. Loose screws are reset with new fasteners, and pulled clips are replaced rather than re-driven.

  3. Repair the dents and seams

    Dents that have not cut the finish are assessed for function, and seams that have lifted are re-sealed or re-joined with the sealant the panel maker names.

  4. Replace the trim and the flashing

    Bent or torn trim, ridge caps and valley metal are replaced with matching pieces, and the new metal is fixed to the same line as the panel it meets.

  5. Record and test the work

    The repaired areas are tested with water where the roof allows, and the record lists each panel, seam and fastener by position with photographs.

Muscogee County

Why metal roof repair is different in Chattahoochee Valley

The FACTS sheet records the 1 March 2007 EF-2 tornado's heaviest damage in the 6200 block of Brookstone Boulevard, which is a reason to look at metal trim and panels on north-metro roofs after a named event.

Metal roofs in the Alabama towns across the Chattahoochee are repaired by the same method, and the roofer confirms the local rules for each side.

FACTS.md gives no local roof-type share, so this page does not say how many metal roofs there are in the city.

Where we work

Metal Roof Repair across Muscogee County

Not sure if you're covered? Check your ZIP code.

Related

Flashing and Chimney Repair

Repairing the flashing at chimneys, walls, vents and skylights in Columbus, where wind and storm debris most often open a roof.

Storm and Wind Roof Inspection

A written roof inspection after a storm in Columbus and the towns around it, with the damage separated from wear and recorded.

Full Roof Replacement

Replacing a whole roof in Columbus and the towns around it, from tear-off to the final flashing, quoted line by line on site.

FAQ

Metal Roof Repair FAQs

Can I walk on a metal roof to check it?

Not safely in most cases, and never when it is wet. Check from the ground and from the attic, and let the roofer walk the roof.

Will a dent void the warranty?

It can, depending on the manufacturer's terms. Ask the roofer to confirm the warranty position in writing before any repair.

Are metal roofs noisy in a storm?

Sound depends on the roof's construction and the decking. A roofer can explain whether a repair affects the sound, but this page makes no claim about it.

How long does a metal roof repair take?

Most repairs are done in a single visit. Larger work with panel replacement takes longer, and the roofer confirms the time.

WhatsApp